|
EVOLUTION VIII-IX - CAMBER & TOE ADJUSTMENT
///
BACK TO TOP |
|
|
STM EVO 8/9 OEM REAR TOE ADJUSTMENT BOLT KIT
The STM Rear Toe Adjustment Bolt Kit is comprised of all OEM Mitsubishi bolts for a clean install. Kit as pictured is for one side. You will need to purchase two for both sides.
2003-2006 Evolution VIII & IX.
OEM-EVO-RTAB |
|
STM EVO 8/9 OEM REAR CAMBER ADJUSTMENT BOLT KIT
The STM Rear Camber Adjustment Bolt Kit is comprised of all OEM Mitsubishi bolts for a clean install. You will need to purchase two for both sides. These kits are different for the VIII and IX.
2003-2005 Evolution VIII.
2006 Evolution IX MIVEC.
OEM-EVO8-RCAB,OEM-EVO9-RCAB |
|
STM EVO 8/9 OEM FRONT BALL JOINT NUT & BOLT KIT
The STM Front Ball Joint Nut & Bolt Kit is comprised of all OEM Mitsubishi bolts for a clean install. These kits are different for the VIII and IX.
2003-2005 Evolution VIII.
2006 Evolution IX MIVEC.
OEM-EVO8-FBJBK,OEM-EVO9-FBJBK |
|
H&R EVO 8/9 TRIPLE C CAMBER ADJUSTMENT BOLTS
Whenever you lower a vehicle's ride height, negative camber is increased. Just how much depends on the vehicle and the reduction in ride height. H&R "Triple C" Camber Adjustment Bolts are a simple, yet very effective means of removing excessive camber, adjusting your vehicle's camber settings, or even correcting small side-to-side camber variations for precise alignment.
2003-2006 Evolution VIII & IX.
TC114 |
|
OEM MITSUBISHI EVO 8/9 REAR SWAY BAR LINKS
Genuine OEM Mitsubishi Rear Sway Bar Links.
2003-2006 Evolution VIII & IX CT9A.
4056A027,4056A028 |
|
WHITELINE EVO 8/9 REAR SWAY BAR LINK ASSEMBLY
Whiteline Sway Bar Link Assembly utilizes heavy duty, steel ball-joint ends that can adjust and rotate to any angular combination. Eliminate sway bar preload via the adjustable body providing up to 15mm center to center length adjustment.
2003-2006 Evolution VIII & IX.
KLC102 |
|
WHITELINE EVO 8/9 FRONT SWAY BAR LINK ASSEMBLY
The Whiteline Front Sway Bar Link Assembly utilizes a high tensile spring steel link fitted with ultra low compliance polyurethane bushes.
2003-2006 Evolution VIII & IX.
KLC139 |
|
WHITELINE EVO 8/9 ROLL CENTER/BUMP STEER CORRECTION KIT
Whiteline Roll Center / Bump Steer Correction Kit is designed to raise the front, roll-center geometry by using specially engineered ball-joints & tie rod ends while still maintaining original steering geometry. Front roll geometry actually encourages roll the lower you go.
2003-2006 Evolution VIII & IX.
KCA395 |
|
WHITELINE EVO 8/9 SPARE DUST BOOT KIT
Whiteline Spare Dust Boot Kit for the 2003-2015 Evolution VIII-IX-X Bump Steer Correction Kit KCA395 above.
2003-2006 Evolution VIII & IX.
W0903 |
|
OUTER TIE ROD END
Genuine OEM Mitsubishi Outer Tie Rod End fits all the 2003-2006 Evolution VIII & IX models.
2003-2006 Evolution VIII & IX.
4422A052 |
|
OEM MITSUBISHI EVO 8/9 TIE ROD END COVER
Genuine OEM Mitsubishi Tie Rod End Cover fits all Evolution VIII & IX models and all 1990-1999 1G & 2G DSM. Sold individually. Price is for one cover.
2003-2006 Evolution VIII & IX.
MB616023 |
|
OEM MITSUBISHI EVO 8/9 TRAILING & CONTROL ARM BOOT COVER
OEM Mitsubishi Rear Suspension Trailing Arm Boot Cover / Control Arm Boot Cover.
2003-2006 Evolution VIII & IX.
MB808555 |
|
OEM MITSUBISHI EVO 8/9 REAR SUSPENSION STABILIZER LINK COVER
Genuine OEM Mitsubishi Rear Suspension Stabilizer Link Cover fits the 1G & 2G DSM models, Evo 8/9 and 3000GT.
2003-2006 Evolution VIII & IX.
MB518785 |
|
OEM MITSUBISHI EVO 8/9 INNER TIE ROD END
OEM Mitsubishi Inner Tie Rod End.
2003-2006 Evolution VIII & IX.
MR403099 |
|
WHITELINE EVO 8/9 ANTI-LIFT / CASTER CORRECTION KIT
The Whiteline Race-Only Anti-Lift / Caster Correction Kit features light weight aluminium bushings and offset serviceable bearings for added caster, minimal compliance and optimum feedback. Alloy bushings & spherical bearing (adds +0.5°)
2003-2006 Evolution VIII & IX.
KCA400M |
|
WHITELINE EVO 8/9 REAR BUMP STEER CORRECTION KIT
Whiteline Bump Steer Correction Kits are designed to correct suspension geometry improving dynamic toe settings during wheel travel. A reduction to bump steer results in sharper handling and reduced understeer. Bushings must be pressed in and out for installation.
2003-2006 Evolution VIII-IX.
KCA388 |
|
|
EVOLUTION VIII-IX - REAR ARMS & BUSHINGS
///
BACK TO TOP |
|
|
AGENCY POWER EVO 8/9 REAR ADJUSTABLE CONTROL ARMS
Improving rigidity and handling and the vehicles dynamics, These adjustable rear control arms will allow you to setup extra camber and toe settings in the rear. The stock adjustments only allow for minimal changes, the AP arms give you a much more aggressive setup.
2003-2006 Evolution VIII & IX.
AP-CT9A-200 |
|
WHITELINE EVO 8/9 REAR CONTROL ARM
INNER TOE BUSHING KIT
The Whiteline Rear Inner Toe Control Arm Bushing Kit fits all the Evolution VIII & IX models. Click for exact placement.
2003-2006 Evolution VIII-IX.
W0588 |
|
WHITELINE EVO 8/9 REAR UPPER CONTROL ARM
FRONT BUSHING KIT
The Whiteline Rear Control Arm Front Upper Bushing Kit fits all the Evolution VIII & IX models. Click for exact placement.
2003-2006 Evolution VIII-IX.
W0590 |
|
TORQUE SOLUTION EVO 8/9 REAR UPPER CONTROL ARM
INNER BUSHING KIT
Torque Solution polyurethane control arm bushings replace the inner rubber material that over time deteriorates and fails. Leaving you with a sloppy, squeaky suspension. Made from 75a durometer polyurethane. Each mount includes 2 half's and a center steel sleeve. These give you improved traction and reduced wheel hop without too much vibration.
2003-2006 Evolution VIII-IX.
TS-EV8-116 |
|
WHITELINE EVO 8/9 REAR UPPER CONTROL ARM
INNER BUSHING KIT
The Whiteline Rear Control Arm Upper/Inner Bushing Kit fits all the Evolution VIII & IX models. Click for exact placement.
2003-2006 Evolution VIII-IX.
W0591 |
|
OEM MITSUBISHI REAR LOWER CONTROL ARM
INNER BUSHING
Genuine OEM Mitsubishi Evo 8/9 Rear Suspension Lower Arm Bushing for the 2003-2006 Mitsubishi Lancer Evolution VIII-IX. Click for exact placement.
2003-2006 Evolution VIII & IX.
4113A063 |
|
WHITELINE EVO 8/9 REAR LOWER CONTROL ARM
INNER BUSHING KIT
The Whiteline Rear Lower Control Arm Inner Bushings fit all the Evolution VIII & IX models. Click for exact placement.
2003-2006 Evolution VIII-IX.
W62951 |
|
OEM MITSU REAR LOWER CONTROL ARM
OUTER BUSHING
Genuine OEM Mitsubishi Evo 8/9 Rear Suspension Lower Arm Bushing for the 2003-2006 Mitsubishi Lancer Evolution VIII-IX. Click for exact placement.
2003-2006 Evolution VIII & IX.
4113A062 |
|
WHITELINE EVO 8/9 REAR LOWER CONTROL ARM
OUTER BUSHING KIT
The Whiteline Rear Control Arm Lower Outer Bushing Kit fits all the Evolution VIII & IX models. Click for exact placement.
2003-2006 Evolution VIII-IX.
W62950 |
|
OEM MITSUBISHI REAR LOWER CONTROL ARM
SHOCK ABSORBER BUSHING
Genuine OEM Mitsubishi Evo 8/9 Rear Suspension Lower Arm Bushing for the 2003-2006 Mitsubishi Lancer Evolution VIII-IX. Click for exact placement.
2003-2006 Evolution VIII & IX.
MR403464 |
|
WHITELINE EVO 8/9 REAR LOWER CONTROL ARM
SHOCK ABSORBER BUSHING KIT
The Whiteline Rear Lower Control Arm Shock Absorber Bushing Kit fits all the Evolution VIII & IX models. Click for exact placement.
2003-2006 Evolution VIII-IX.
W32958 |
|
WHITELINE EVO 8/9 REAR LOWER CONTROL ARM
SHOCK ABSORBER BUSHING KIT
The Whiteline Rear Control Arm Lower Shock Absorber Bushing Kit fits all the Evolution VIII & IX models. Click for exact placement.
2003-2006 Evolution VIII-IX.
W0589 |
|
WHITELINE EVO 8/9 REAR TRAILING ARM
FRONT LOWER BUSHING KIT
The Whiteline Rear Trailing Arm Front Lower Bushing Kit fits all the Evolution VIII & IX models. Click for exact placement.
2003-2006 Evolution VIII-IX.
W0594 |
|
ENERGY SUSPENSION EVO 8/9 REAR TRAILING ARM
FRONT LOWER BUSHING KIT
Energy Suspension Rear Trailing Arm Bushing Set maintains proper alignment under extreme conditions and improves vehicle handling, cornering and overall control. Full floating, for smoother operation. Available black or red.
2003-2006 Evolution VIII-IX.
5.3134G,5.3134R |
|
|
EVOLUTION VIII-IX - FRONT ARMS & BUSHINGS
///
BACK TO TOP |
|
|
OEM MITSUBISHI EVO 8/9 FRONT LOWER SUSPENSION ARMS
Genuine OEM Mitsubishi Front Lower Suspension Arms.
2003-2006 Evolution VIII & IX.
MR554813,MR554814 |
|
ENERGY SUSPENSION EVO 8/9 FRONT CONTROL ARM BUSHINGS
Energy Suspension Front Control Arm Bushing Set maintains proper alignment under extreme conditions and improves vehicle handling, cornering and overall control. Full floating, for smoother operation. Made of Energy's HYPER-FLEX performance polyurethane to add performance and durability.
2003-2006 Evolution VIII-IX.
5.3133G,5.3133R |
|
WHITELINE EVO 8/9 FRONT CONTROL ARM
LOWER INNER FRONT BUSHING KIT
The Whiteline Front Control Arm Lower Inner Front Bushing Kit fits all the 2003-2015 Evolution VIII, IX & X models. Over compliant front control arm bushings have a huge influence on vehicle stability, steering precision and braking efficiency. Whiteline's kit is specially designed to improve deflection rates for improved response and chassis control.
2003-2006 Evolution VIII-IX.
W0593 |
|
|
EVOLUTION VIII-IX - BARS, BRACING & BUSHING SETS
///
BACK TO TOP |
|
|
STM EVO 8/9 FRONT BUMPER SUPPORT BAR
The STM Front Bumper Support is designed to give you an extra piece of mind if you've removed your heavy, factory bar and you've lost the bumper support. Made in-house of 1 5/8" chromoly steel and finished with a durable, black powdercoat, this piece still weighs less than factory coming in at only 7.5 pounds. Purchase both Front & Rear Bars together and save $50!
2003-2006 Evolution VIII & IX.
STM-EVO89-BSF |
|
STM EVO 8/9 REAR BUMPER SUPPORT BAR
The STM Rear Bumper Support is designed to fit both Evo VIII and JDM IX rear bumpers. Made in-house of 1 5/8" chromoly steel, weighing in at only 6 pounds and finished with a durable, gloss black powdercoat. New mounting hardware is also included for the bar and new stainless hardware for the license plate.
2003-2006 Evolution VIII & IX.
STM-EVO89-BSR |
|
CUSCO EVO 8/9 FRONT MEMBER POWER BRACE
The Cusco Power Brace is designed to stiffen your Evo and improve handling by connecting key portions of the chassis. Features a bolt-on installation, using factory holes, bolts and nuts. Fits all 2003-2006 Evolution 8/9 models, but you will need to remove your factory bumper beam. May not clear all aftermarket intercoolers. Please do your research before purchase.
2003-2006 Evolution VIII & IX.
564 492 FM |
|
WHITELINE EVO 8/9 REAR STRUT TOWER BRACING
Whiteline Strut Tower Bracings are very simple to install and feature a light weight polished aluminium channel and powder coated mounting plates. Kit includes quick release clamps.
2003-2006 Evolution VIII & IX.
KSB628Q |
|
H&R EVO 8/9 SPORT SWAY BARS
H&R Sport Sway Bars are designed for drivers who desire improved handling without lowering or affecting ride quality. Increase your suspension's roll stiffness or its resistance to roll-in turns while maintaining ride comfort and dramatically increasing cornering control, lateral stability, and grip.
2003-2006 Evolution VIII & IX.
70210,71210 |
|
WHITELINE EVO 8/9 FRONT & REAR SWAY BAR KITS
The Whiteline Front & Rear Sway Bar Kits fit all the Evolution VIII & IX models. Engineered to "Activate more grip" this packaged solution designed to improve performance and enhance the driving experience of your vehicle.
2003-2006 Evolution VIII & IX.
BMK009,BMK009M |
|
WHITELINE EVO 8/9 26MM FIXED POSITION FRONT SWAY BAR
The Whiteline 26mm fixed position sway bar = more grip = better handling = outright performance! It's the best dollar for dollar handling improvement you can make to your vehicle.
2003-2006 Evolution VIII & IX.
BMF48 |
|
WHITELINE EVO 8/9 24MM X-HEAVY DUTY REAR SWAY BAR
The Whiteline 24mm, X-Heavy Duty 3-Point adjustable sway bar allows its rate to be altered by increasing or reducing the length of the lever arms. This permits the roll stiffness to be tuned for different situations without replacing the entire bar.
2003-2006 Evolution VIII & IX.
BMR65XZ |
|
WHITELINE EVO 8/9 26MM XX-HEAVY DUTY REAR SWAY BAR
The Whiteline 26mm, XX-Heavy Duty 3-Point adjustable sway bar allows its rate to be altered by increasing or reducing the length of the lever arms. This permits the roll stiffness to be tuned for different situations without replacing the entire bar.
2003-2006 Evolution VIII & IX.
BMR65XXZ |
|
WHITELINE EVO 8/9 24MM HEAVY DUTY REAR SWAY BAR MOUNT KIT
Whiteline heavy duty rear sway bar mounting saddle kits are designed to replace the original equipment mounts with a stronger more rigid version. This Whiteline kit improves sway bar response & should be used for large diameter or adjustable sway bars especially when running the stiffer sway bar settings as factory mounts will twist/ flex & potentially fail prematurely.
2003-2006 Evolution VIII & IX.
KBR22-24 |
|
WHITELINE EVO 8/9 24MM FRONT SWAY BAR BUSHINGS
Whiteline 24mm Sway Bar Bushings. Whiteline sway bar products improve sway bar effectiveness for more balanced and predictable cornering.
2003-2006 Evolution VIII-IX.
W22960 |
|
WHITELINE EVO 8/9 22MM REAR SWAY BAR BUSHINGS
Whiteline 22mm Rear Sway Bar Bushings for the Evolution VIII & IX models.
2003-2006 Evolution VIII-IX.
W22959 |
|
BUSCHUR RACING EVO 8/9 FRONT CROSS MEMBER BRACE
This is designed to replace the member that is located under the front of your Evolution that runs front to rear. Made of lightweight chromoly tubing this item saves 6.2 pounds of weight from the stock member.
2003-2006 Evolution VIII-IX.
BR-EVO-CROSSM |
|
BUSCHUR RACING EVO 8/9 "MOUSTACHE BAR" (REAR DIFF SUPPORT)
This is the Buschur Racing Rear Differential Support, or called by some the "Moustache Bar." This holds the rear differential in place. The rediculously heavy stock bar weighed 15.9 pounds! While the new Buschur piece holds strong at only 3.2 pounds! You can shed almost 13 pounds off the car with this one piece!
2003-2006 Evolution VIII-IX.
BR-EVO-MOUSTACHE |
|
BUSCHUR RACING EVO 8/9 DRIVESHAFT LOOP
Made of chrome moly, it bolts into existing holes in the car with the side brackets leaving room to fit the buschur 3" exhaust through/past it too. If the front of the u-joint, yoke or driveshaft itself breaks the driveshaft can dig into the pavement or come through the floor and take your legs out. This is meant to prevent that from happening.
BR-EVO-DS-LOOP |
|
OEM MITSUBISHI EVO 8/9 FRONT AXLE CROSS MEMBER BRACES
Genuine OEM Mitsubishi Front Axle Cross Member Braces. Rear brace is pictured. Front brace has only 2 holes.
2003-2006 Evolution VIII & IX.
MR554452,MR554451 |
|
OEM MITSUBISHI EVO 8/9 FRONT SUSPENSION CROSSMEMBER
Genuine OEM Mitsubishi Front Suspension Crossmember fits all the Evolution VIII & IX models.
2003-2006 Evolution VIII & IX.
MR554447 |
|
OEM MITSUBISHI EVO 8/9 FRONT AXLE CROSSMEMBER NUT
Genuine OEM Mitsubishi Front Axle Crossmember Nut fits all the Evolution VIII & IX models.
2003-2006 Evolution VIII & IX.
MD090875 |
|
BUSCHUR RACING EVO 8/9 REAR DIFF SIDE SUPPORT BRACKETS
This is Buschur's lightweight, billet aluminum solution to those rusted chunks of steel that currently bolt to the sides of your rear diff. These new Side Differential Support Brackets weighed in at only 4.25 pounds and completely replace the stock part with no need to replace the rubber bushing.
2003-2006 Evolution VIII-IX.
BR-EVO-DIFF-SUP |
|
TORQUE SOLUTION EVO 8/9 MUSTACHE BAR ELIMINATOR KIT
Designed to eliminate that annoying rear diff "clunk" under hard shifts from the rear of your car. Made from 100% billet 6061 aluminum and CNC machined for accurate tolerances. The urethane bushings are less harsh and transmit less feedback into the cabin then the solid bushings. Bushings are REQUIRED for install, but you can purchase just the mount if you already have them.
2003-2006 Evolution VIII-IX.
TS-EV8-005,TS-EV8-004,TS-EV8-003 |
|
ENERGY SUSPENSION EVO 8/9 REAR DIFF BUSHING SET
Sick of that "Thunk" when you shift hard into the next gear? These will take care of that. Energy Suspension's HYPER-FLEX performance polyurethane rear differential/moustache bar bushing set is made in the USA.
2003-2006 Evolution VIII-IX.
5.1108G,5.1108R |
|
PROTHANE EVO 8/9 TOTAL SUSPENSION BUSHING KIT
The Prothane Total Suspension Bushing Kit for Evo VIII-IX is available in black or red and includes bushings for the front and rear sway bar, front and rear control arm and mustache bar.
2003-2006 Evolution VIII-IX.
13-2003,13-2003-BL |
|
ENERGY SUSPENSION EVO 8/9 MASTER BUSHING SET
Energy's complete Master Set restores worn mounts and bushings as well as adding a dramatically higher degree of performance. Special formula HYPER-FLEX performance polyurethane components, which is higher durometer (firmness) material and re-engineered performance-minded components, assures long-lasting performance that O.E.M. bushings and mounts just can't offer.
2003-2006 Evolution VIII-IX.
5.18115G,5.18115R |
|
WHITELINE EVO 8/9 STEERING PRECISION KIT
Whiteline Steering Precision Kit (Steering Rack & Pinion Mount Bushing) is designed to improve the steering precision and response while reducing understeer and increasing front grip specifically on turn-in. This is achieved through the use of low compliance replacement mounting bushes and special spacers to alter steering geometry.
2003-2006 Evolution VIII & IX.
KCA390 |
|
MITSUBISHI PARTS
Take a look here to see even more OEM parts. STM has a MASSIVE stock of Mitsubishi parts on hand from tiny clips and gaskets to must-have JDM rears. If you can't find what you need, just give us a shout, if Mitsubishi still makes it, we can get it for you!
2003-2006 Mitsubishi Lancer Evolution VIII-IX.
MITSUBISHI |
|
