MITSUBISHI > 1990-1999 DSM > ELECTRONICS, BATTERY & IGNITION > SENSORS & INSTALL ACCESSORIES

1990-1999 DSM - GAUGE INSTALLATION      ///      BACK TO TOP
	STM REMOTE OIL PRESSURE LINE KIT (OIL FILTER HOUSING) The STM Remote Oil Pressure Line Kit includes everything needed to take your oil psi gauge reading from the oil filter housing. Works with any 1/8" NPT sending unit. 1990-1999 1G & 2G DSM. STM-DSM-EVO-89-REMOTE-OIL, (OLD# STM-DSM-OPSI-F)
	STM REMOTE OIL PRESSURE LINE KIT (CYLINDER HEAD) The STM Remote Oil Pressure Line Kit includes everything needed to take your oil psi gauge reading from the cylinder head. Works with any 1/8" NPT sending unit. 1990-1999 1G & 2G DSM. STM-DSM-OPSI
	BOOST GAUGE INSTALL KIT This allows you to tap your mechanical gauge that uses the 1/8 tubing as a feed line. Universal Application. STM-BGIK
	PIGTAIL FUSES Trying to find a power source for your gauges? These nifty, little things will do the trick! Universal Application. STM-PIGF
	PROSPORT OIL FILTER ADAPTER PLATE (M20 x 1.5) This is a great product from Prosport to make installing your Oil Pressure and Oil Temperature senders easy. This plate screws on under your oil filter and it has 4 1/8"NPT fittings. M20 x 1.5 fits most Subaru, Non-metric Honda, Mitsubishi, Acura, Hyundai, Nissan Sentra 2.5L & Mazda RX-7, RX-8 & S2000. Universal Application. PSOPOT M20XP1.5
	PROSPORT WATER TEMP SENSOR ADAPTER This will place the temperature sensor directly in the stream of the water towards the radiator without absorbing transient heat from the engine block for accurate readings of the water temperature. Four sizes are available for the perfect fit for just about any engine application and stays water-tight to prevent leaks with the provided hose clamps. Each adapter features an 1/8 NPT fitting. Universal Application. PSWT3
	TUBING FOR MECHANICAL PSI GAUGES Auto Meter Nylon Tubing for Mechanical Pressure Gauges. Does not accommodate fuel pressure or models 5423 & 5426. Universal Application. 3223
	AUTOMETER ADAPTER (1/8" NPT-BSPT) Autometer Metric Gauge Adapter. 1/8" NPT Female to 1/8" BSPT Male Adapter. Universal Application. 2269
	-4AN MALE TO 1/8 NPT FEMALE ADAPTER FITTING -4AN Male to 1/8 NPT Female Adapter Fitting. Universal Application. TF-GA-04
	3M SUPER 33+ ELECTRICAL TAPE Scotch® Vinyl Electrical Tape 33 is a quality, general-purpose vinyl insulating tape. It has excellent resistance to: abrasion, moisture, alkalies, acid, copper corrosion and varying weather conditions. 3/4" x 52' Roll. 3MET33-10
	PROFITTER 500° LOW DENSITY PTFE PIPE TAPE 1/2" x 520" roll pipe sealing tape. 1/2" x 520" Roll. 63164
	VIBRANT POLYETHYLENE AIR LINE TUBING Flexible, lightweight and durable. Suitable for air lines and instrumentation and capable of Withstanding operating pressures up to 100 PSI and temperatures up to 140°F. Sold in a 10 foot roll and available in three diameters: 5/32", 3/8" and 1/4". Universal Application. 2650,2651,2652
	SILICONE VACUUM HOSE High quality, thick-walled, pure silicone hose in 3mm, 4mm and 6mm. Sold Per Foot. XXXXXX
	BLACK T-FITTINGS Black T Vacuum Fittings. 3, 4 and 6mm sizes. Universal Application. 10110,10109,12926,10108
1990-1999 DSM - REPLACEMENT SENSORS & PARTS      ///      BACK TO TOP
	OEM MITSUBISHI OXYGEN SENSORS (95-99 2G DSM) Genuine OEM Mitsubishi front and rear oxygen sensors. Please note, the 1G DSM oxygen sensors are all discontinued from Mitsubishi and no longer available. Sad face. 1995-1999 2G DSM. MD313819,MD185335
	AEM REPLACEMENT 4.9LSU BOSCH OXYGEN SENSOR AEM Replacement 4.9LSU Bosch Oxygen Sensor for new AEM Digital Wideband UEGO Air/Fuel Gauge 30-4110. Universal Application. 30-2004
	AEM REPLACEMENT 4.2LSU BOSCH OXYGEN SENSOR AEM Replacement 4.2LSU Bosch Oxygen Sensor for original AEM Wideband UEGO Air/Fuel Gauges. Universal Application. 30-2001
	AUTOMETER NARROW BAND O2 SENSOR KIT Auto Meter Narrow Band O2 Sensor Kit for use with narrow band air/fuel ratio gauges. Universal Application. 2244
	INNOVATE REPLACEMENT 02 SENSOR (LSU 4.2) Bosch LSU 4.2 5-Wire Wide-Band O2 Sensor. Compatible with Innovate Motorsports LM-1, LM-2, LC-1, and LC-1ST. Universal Application. 3737
	INNOVATE REPLACEMENT 02 SENSOR (LSU 4.9) Bosch LSU 4.9 5-Wire Wide-Band O2 Sensor. Compatible with Innovate Motorsports LM-2, LC-2, and MTX-L, SCG-1, DLG-1, PSB-1, and PSN-1. Universal Application. 17025,3888
	NGK NTK REPLACEMENT O2 SENSOR NGK / NTK replacement oxygen sensor sensor for the AFX wideband monitor. Universal Application. 24302
1990-1999 DSM - MAP & AIT SENSORS      ///      BACK TO TOP
	STM DSM SPEED DENSITY SENSOR KIT If you're switching to Speed Density in your DSM, Evo 8 or 9, you'll need these sensors to get you on your way. The STM Speed Density Sensor Kit includes an AEM AIT sensor with aluminum weld bung and a 4 BAR Omni Power MAP Sensor. 1990-1999 1G & 2G DSM. STM-EVO89/DSM-SDSK
	STM DSM GM SPEED DENSITY SENSOR KIT The STM GM Speed Density Sensor Kit is a much more affordable alternative compared to AEM and includes the GM AIT sensor and matching harness, aluminum weld bung for your intercooler pipe and a 4 BAR Omni Power MAP Sensor. 1990-1999 1G & 2G DSM. STM-KIT-EVO89/DSM-SDSK
	STM UNIVERSAL GM AIR INTAKE TEMPERATURE SENSOR KIT For a less expensive option to the AEM sensors, The STM GM Air Intake Temperature Sensor Kit includes an aluminum weld-on bung for your pipe, GM AIT sensor and matching pigtail harness. Universal Application. STM-GMAIT
	AEM AIR INLET TEMPERATURE SENSOR Air inlet temperature sensor kit. Includes aluminum weld-in bung, connector plug with flying lead & sensor. Universal Application. 30-2010
	DURALAST GM AIT SENSOR PIGTAIL HARNESS Duralast GM air intake temperature sensor female pigtail harness. Typically used with Mitsubishi DSM & Evolution speed density conversions. Universal Application. 235
	DURALAST GM AIT SENSOR Duralast GM 3/8" NPT air intake temperature sensor. Typically used with Mitsubishi DSM & Evolution speed density conversions Universal Application. SU-107
	OMNI POWER MITSUBISHI MAP SENSORS Omni Power USA 3 and 4 Bar MAP (Manifold Absolute Pressure) sensors use state of the art bipolar op amp circuitry with thin film resistor networks built into each micro chip. Pressure changes are calculated on a true linear 0-5 volt scale via a specially designed silicon pressure sensor that also compensates for temperature changes. 1990-1999 1G & 2G DSM. MAP-MITS-3BR,MAP-MITS-4BR
	STM 2G DSM INTAKE MANIFOLD SENSOR ADAPTER The STM Intake Manifold Sensor Adapter gives you an 1/8" NPT thread allowing you to cleanly attach a map sensor, pressure sensor (or any sensor of your choice) directly on your Evo 8/9 or 95-99 DSM factory intake manifold. 1995-1999 2G DSM. STM-EVO/DSM-MAP-F
	AEM REPLACEMENT MAP SENSOR KITS AEM Replacement MAP Sensor Kits include stainless steel sensor, connector, pins, 1/8" NPT to -4AN adapter & 1/8" NPT to 3/16" barb adapter. 1, 2, 3.5 and 5 BAR. Universal Application. 30-2130-15,30-2130-30,30-2130-50,30-2130-75
	AEM MAP SENSOR CONNECTOR AEM Map Sensor Connector. Universal Application. 35-2131
	AEM TRU-BOOST 5 BAR MAP SENSOR UPGRADE KIT AEM Tru-Boost 5 Bar MAP Sensor Upgrade Kit allows your Tru-Boost gauge the capability to read boost up to 50 psi. Universal Application. 30-4351
1990-1999 DSM - ENGINE, GAUGE & MISC SENSORS      ///      BACK TO TOP
	OEM MITSUBISHI KNOCK SENSOR (90-94 1G) Genuine OEM Mitsubishi Knock Sensor. 1990-1994 1G DSM. MD141510
	OEM MITSUBISHI CAMSHAFT POSITION SENSORS (2G 95-99) OEM Mitsubishi Camshaft Position Sensors. 1995 to early 96 is located on the driver side, late 96 to 99 is on the passenger side. 1995-1999 2G DSM. MD327107, MD300102
	OEM MITSUBISHI CRANK POSITION SENSOR (2G 95-99) OEM Mitsubishi Crank Position Sensor. 1995-1999 2G DSM. MD300101
	OEM MITSUBISHI EGR EMISSION SOLENOID VALVE (94-99) OEM Mitsubishi EGR Emission Solenoid Valve Assemblies. Available for 1994+ models. Please check build date before purchase. 1994-1999 1G & 2G DSM Models. MB924421,MR312748,MR312542
	OEM MITSUBISHI WATER TEMPERATURE SENSOR (2G 95-99) Genuine OEM Mitsubishi Water Temperature Sensor fits all 2003-2015 Evolution 8/9/X models as well as the 2G DSM (Eclipse GST/GSX & Talon TSi). 1995-1999 2G DSM. 1308A012
	OEM MITSUBISHI WATER TEMPERATURE SENSOR (1G 90-94) Genuine OEM Mitsubishi Water Temperature Sensor. 1990-1994 1G DSM. MD069879
	OEM MITSUBISHI WATER TEMP GAUGE SENSOR Genuine OEM Mitsubishi Water Temperature Gauge Sensor. 1990-1999 1G & 2G DSM. MD091056
	OEM MITSUBISHI OIL PRESSURE SENDING UNIT Genuine OEM Mitsubishi oil pressure sending unit. 1990-1999 1G & 2G DSM. MD133273
	OEM MITSUBISHI OIL PRESSURE SWITCH OEM Mitsubishi 4G63 Oil Pressure Switch fits all 4G63 DSM. 1990-1999 1G & 2G DSM. 1258A002
	AEM REPLACEMENT PRESSURE SENSOR KITS AEM Replacement PSIg pressure sensors are available from 100-2000 psi for boost, EGT, nitrous, brake pressure, inlet air temperature, or UEGO replacement gauges. Universal Application. 30-2130-100,30-2130-150,30-2130-500,30-2130-1000,30-2130-2000
	AEM REPLACEMENT FLUID PRESSURE SENSORS AEM Replacement Fluid Pressure Sensors are available for 15, 35, 50, 100 and 150 PSI boost and fluid ranges. Compatible with AEM Analog and Digital Gauges. Universal Application. 30-2131-15G,30-2131-50,30-2131-75,30-2131-100,30-2131-150
	AEM REPLACEMENT FLUID TEMPERATURE SENSOR KIT AEM Replacement Oil/Trans/Water Temperature Sensor Kit includes the 1/8"NPT temperature sensor, plug, pins & pin lock. Compatible with digital and analog gauges. Universal Application. 30-2012
	AEM REPLACEMENT METHANOL INJECTION MONITOR SENSOR AEM Replacement Methanol Injection Monitor Sensor. Universal Application. 35-2128
	AEM REPLACEMENT ANALOG EGT K-TYPE SENSOR AEM Replacement EGT Sensor for Analog Gauges. K-Type Closed Tip Thermocouple Sensor. Universal Application. 30-2065
	AEM EXHAUST GAS TEMPERATURE SENSOR KIT The AEM 30-2050 EGT Sensor Kit is a RTD type EGT sensor with an inconel body, M14 x 6H. It includes an RTD temp sensor with male thread, a weld-on bung with female thread, connector and pins and offers a heat range of -40°F to 1832°F. Universal Application. 30-2050
	AEM UNIVERSAL 12 POSITION TRIM POT The AEM Universal 12 Position Trim Pot is for use on virtually any Engine Management System, such as the AEM EMS. Use the Trim Pot to adjust a number of trims, including ignition timing, fuel, boost, etc. Universal Application. 30-2056
1990-1999 DSM - CABLES & HARNESSES      ///      BACK TO TOP
	EVOSCAN OBD2 REFLASH CONNECTOR (98-99 2G DSM) The EvoScan OBD2 Reflash Connector is an additional or replacement accessory for an OpenPort 2.0 cable for reflashing. EvoScan Openport 1.3R / 1.3U USB Cables do NOT need this adapter, this 12 pin connector is already permanently attached to those. 1998-1999 2G DSM. MITSI_CONNECTOR
	SHERIDAN ENGINEERING AMP CONNECTOR (TYPE-B) The 1P 250 SENDER connector is an Amp connector, the OEM supplier. It is a .250 wide receptacle connector. It is commonly used to attach to 1 wire gauge senders and switches. What makes it different is that the locking mechanism is on the terminal itself, and not on the plastic housing. The plastic housing has the release mechanism built in. 1990-1999 1G & 2G DSM. CON-1P250SENDER-B
	SHERIDAN ENGINEERING CAS HARNESS (1G TO 95-96 DSM) This harness will adapt a 1G CAS into a 95-96 DSM, perfect for 1G engine swaps. It connects at the CAS, and then plugs into the 2G cam and crank sensor connectors. 1G CAS into a 95-96 DSM. HAR-1G2G95
	SHERIDAN ENGINEERING CAS HARNESS (1G TO 97-99 DSM) This harness will adapt a 1G CAS into a 97-99 DSM, perfect for 1G engine swaps. It connects at the CAS, and then plugs into the 2G crank sensor. Requires splicing 1 wire into the 2G cam sensor wiring. 1G CAS in a 1997-1999 DSM. HAR-1G2G97
	SHERIDAN ENGINEERING CAM ANGLE SENSOR PIGTAIL (90-94 1G DSM) This pigtail is designed to replace the 1G CAS connector and wiring, perfect for replacing damaged connectors and harnessing. 1990-1994 1G DSM. 4001003
	SHERIDAN ENGINEERING ENGINE COOLANT TEMP SENSOR (2G 95-99 DSM) The Sheridan Engineering Engine Coolant Temp Sensor is a TYCO connector, the same OEM Mitsubishi supplier. This sensor is green instead of the factory black. Includes new wire seals and terminals to match. 1995-1999 2G DSM. CON-2GECT
	SHERIDAN ENGINE HARNESS CONNECTOR KIT (1G TO 2G SWAP) The Sheridan Engineering Engine Harness Connector Kits will allow vehicle owners to repair their harnesses, or build new ones. The kits include the connectors listed, wire terminals and seals. These kits include only the harness side connectors. 1G Engine Swap in a 2G 1995-1999 DSM. KIT-951GBASE
	SHERIDAN ENGINE HARNESS CONNECTOR KIT (1990 1G DSM) The Sheridan Engineering Engine Harness Connector Kits will allow vehicle owners to repair their harnesses, or build new ones. The kits include the connectors listed, wire terminals and seals. These kits include only the harness side connectors. 1990 1G DSM. KIT-90BASE
	SHERIDAN ENGINE HARNESS CONNECTOR KIT (91-94 1G DSM) The Sheridan Engineering Engine Harness Connector Kits will allow vehicle owners to repair their harnesses, or build new ones. The kits include the connectors listed, wire terminals and seals. These kits include only the harness side connectors. 1991-1994 1G DSM. KIT-91BASEKIT
	SHERIDAN ENGINE HARNESS CONNECTOR KIT (95-96 2G DSM) The Sheridan Engineering Engine Harness Connector Kits will allow vehicle owners to repair their harnesses, or build new ones. The kits include the connectors listed, wire terminals and seals. These kits include only the harness side connectors. 1995-1996 2G DSM. KIT-95BASE
	SHERIDAN ENGINE HARNESS CONNECTOR KIT (97-99 2G DSM) The Sheridan Engineering Engine Harness Connector Kits will allow vehicle owners to repair their harnesses, or build new ones. The kits include the connectors listed, wire terminals and seals. These kits include only the harness side connectors. 1997-1999 2G DSM. KIT-97BASE
	AEM INFINITY SERIES 7 UNIVERSAL PLUG & PIN KIT The AEM Infinity Series 7 Universal Plug & Pin Kit includes (1) 73-pin connector with cover, (1) 56-pin connector with cover, 130 small pins, 1 large pin with weather seal, 1 micro relay with pins, and 30 sealing plugs. AEM offers several different wiring harness types and configurations to simplify the process of wiring the Infinity ECU to your vehicle. Universal Application. 30-3701
	AEM INFINITY SERIES 7 UNIVERSAL WIRING HARNESS The AEM Infinity Series 7 Universal Wiring Harness includes pre-wired power and grounds, power relay, fuse box, dual wideband connectors, AEMnet connector (CAN), 100 X 96" terminated wires for population and 12 small pins. AEM offers several different wiring harness types and configurations to simplify the process of wiring the Infinity ECU to your vehicle. Universal Application. 30-3702
	AEM INFINITY SERIES 7 MINI UNIVERSAL WIRING HARNESS The AEM Infinity Series 7 Mini Universal Harness includes pre-wired power and grounds, power relay, fuse box, dual wideband connectors, AEMnet connector (CAN), 100 small pins with 30 sealing plugs. AEM offers several different wiring harness types and configurations to simplify the process of wiring the Infinity ECU to your vehicle. Universal Application. 30-3703
	AEM INFINITY SERIES 5 PLUG & PIN KIT The AEM Infinity Series 5 Plug & Pin Kit includes 80 pin connector with cover, 80 small pins, 1 micro relay with pins and 30 sealing plugs. AEM offers several different wiring harness types and configurations to simplify the process of wiring the Infinity ECU to your vehicle. Universal Application. 30-3704
	AEM INFINITY SERIES 5 MINI UNIVERSAL WIRING HARNESS The AEM Infinity Series 5 Mini Universal Harness includes pre-wired power, grounds, power relay, fuse box, single wideband & AEMnet, 80 small pins and 30 sealing plugs. AEM offers several different wiring harness types and configurations to simplify the process of wiring the Infinity ECU to your vehicle. Universal Application. 30-3705
	AEM INFINITY SERIES 5 UNIVERSAL MINI FLYING LEAD HARNESS The AEM Infinity Series 5 Universal Mini Flying Lead Harness includes pre-wired power, grounds, power relay, single wideband, 8 x coils & 8 x injectors. I/O wiring includes TPS, MAP, CLT, AIT, +5V, Sensor Ground, Fan, Tach & 2 Step. 10 x 96" 22ga Terminated wire and 2 x 96" Terminated 2-Pair Twisted/Shielded Wire. AEM offers several different wiring harness types and configurations to simplify the process of wiring the Infinity ECU to your vehicle. Universal Application. 30-3706
	AEM INFINITY 02 SENSOR EXTENSION HARNESS The AEM Infinity 02 Sensor Extension Harness allows you to connect your AEM wideband O2 air/fuel ratio sensors to the Infinity's on-board wideband UEGO controllers. 72" length. Universal Application. 30-3600
	AEM INFINITY AUX HARNESS FOR AIT AND MAP SENSOR The AEM Infinity Aux Harness for AIT and MAP Sensor allows you to connect your AEM AIT and MAP sensors to the Infinity's Aux Deuatch Plug. 72" length. Universal Application. 30-3510-00
	AEM INFINITY IP67 COMMUNICATIONS CABLE Protect your AEM Infinity ECU by using IP67-rated communications cables. They are completely dustproof and are rated waterproof to 1 meter. Universal Application. 30-3601
	AEM INFINITY IP67 LOGGING CABLE Protect your AEM Infinity ECU by using IP67-rated communications cables. They are completely dustproof and are rated waterproof to 1 meter. Universal Application. 30-3602
	AEM PRESSURE SENSOR REPLACEMENT HARNESS FOR DIGITAL GAUGES The AEM Digital Boost/Pressure Gauge Replacement Cable replaces your old, damaged harness. This 8 foot cable fits AEM Digital Gauges (30-4401, 30-4406, 30-4407 & 30-4408). Universal Application. 35-3405
	AEM PRESSURE SENSOR REPLACEMENT HARNESS FOR ANALOG GAUGES AEM 96" Sensor Replacement Harness for Analog Boost/Fuel/Oil Pressure Gauges. Universal Application. 35-3412
	AEM REPLACEMENT TRU-BOOST 5 BAR MAP SENSOR HARNESS AEM 96" Replacement Harness for Tru-Boost 5 Bar MAP Sensor Upgrade Universal Application. 35-3410
	AEM TRU-BOOST GAUGE REPLACEMENT CABLE The AEM True-Boost Replacement Cable fits the AEM Digital Tru-Boost Gauge (30-4350) and is 8 feet long. Universal Application. 35-3409
	AEM REPLACEMENT UEGO POWER HARNESS The AEM Replacement UEGO Power Harness is compatible with both the Bosch 4.2 & 4.9 LSU sensors. 36" length. Universal Application. 35-3401
	AEM REPLACEMENT UEGO 4.2LSU OXYGEN SENSOR HARNESS AEM 96" Replacement UEGO 4.2LSU Oxygen Sensor Harness. Universal Application. 35-3400
	AEM REPLACEMENT UEGO 4.9LSU OXYGEN SENSOR HARNESS AEM 96" Replacement UEGO 4.9LSU Oxygen Sensor Harness. Universal Application. 35-3441
	AEM WIDEBAND FAILSAFE O2 SENSOR REPLACEMENT HARNESS AEM 96" 4.2LSU O2 Sensor Replacement Harness for Wideband Failsafe Gauge 30-4900. Universal Application. 35-3426
	AEM REPLACEMENT ANALOG TEMPERATURE SENSOR HARNESS AEM 96" Replacement Temperature Sensor Harness for the Oil/Transmission/Water Temp Analog Gauges. Universal Application. 35-3413
	AEM DIGITAL VOLT GAUGE POWER REPLACEMENT HARNESS AEM 36" Power Replacement Harness for Digital Volt Gauge 30-4400. Universal Application. 35-3403
	AEM DIGITAL TEMPERATURE GAUGE REPLACEMENT HARNESS AEM 96" Replacement Harness for the Digital Oil/Transmission/Water Temperature Gauge 30-4402. Universal Application. 35-3404
	AEM REPLACEMENT METH FLOW/FAILSAFE GAUGE USB CABLE AEM 96" Replacement USB Cable for AEM Meth Flow/Failsafe Gauges. Universal Product. 35-3415
	AEM REPLACEMENT ANALOG EGT SENSOR HARNESS AEM 96" Replacement EGT Sensor Harness for Analog Gauges. Universal Application. 35-3414
	AEM WIDEBAND FAILSAFE REPLACEMENT POWER HARNESS AEM 36" Replacement Power Harness for the Wideband Failsafe Gauge 30-4900. Universal Application. 35-3425
	AEM ANALOG GAUGE POWER HARNESS AEM 36" Power Replacement Cable for Analog Gauges. Universal Application. 35-3411
	AEM REPLACEMENT METH FAILSAFE OUTPUT HARNESS AEM 36" Replacement Output Harness for Water/Methanol Failsafe Gauges. Universal Product. 35-3418
1990-1999 DSM - SOLENOIDS      ///      BACK TO TOP
	AEM BOOST CONTROL SOLENOID AEM's Boost Control Solenoid is specifically manufactured for automotive applications. It is designed to resist corrosion and sticking from exposure to rich fuel mixtures. AEM's Boost Control Solenoid is pressure tested to 100 PSI and includes 1/8" NPT to 3/8" barb fittings to reduce any chance of leaks. Universal Application. 30-2400
	PERRIN 3-PORT ELECTRONIC BOOST CONTROL SOLENOID The EBCS PRO operates almost 2 times faster than other designs, allowing almost 50% more airflow, and works with OEM ECUs without causing check engine lights. To fully utilize the EBCS Pro, an ECU recalibration is NEEDED to ensure no overboosting occurs. The OEM male connector is specific to all Subaru and Mitsubishi applications. Includes additional brackets to allow universal applications. Universal Application. ASM-TAC-726

CSS