MITSUBISHI > EVOLUTION VIII-IX > ELECTRONICS, BATTERY & IGNITION > SENSORS, WIRING & INSTALL

EVOLUTION VIII-IX - GAUGE INSTALLATION      ///      BACK TO TOP
	STM EVO 8/9 REMOTE OIL PRESSURE LINE KIT (BACK OF BLOCK) The STM Remote Oil Pressure Line Kit works with 1/8" NPT gauges and installs in place of your factory oil pressure switch in the back of your engine block allowing you to relocate your new oil pressure sending unit away from the harsh vibrations of the engine, keeping your sending unit safe and prolonging life. Works with both 4G63 and 4B11 Evolution 8/9/X. 2003-2006 Evolution VIII & IX. STM-EVO-89-REMOTE-OP
	STM EVO 8/9 REMOTE OIL PRESSURE LINE KIT (OIL FILTER HOUSING) The STM Remote Oil Pressure Line Kit includes everything needed to take your oil psi gauge reading from the oil filter housing. Works with any 1/8" NPT sending unit. 2003-2006 Evolution VIII & IX. STM-DSM-EVO-89-REMOTE-OIL
	STM EVO 8/9 WATER NECK WITH NPT TEMP SENSOR BUNG The STM Evo VIII-IX Water Neck starts with an OEM Mitsubishi piece, modified to accommodate a 1/8" NPT bung for a clean install with your water temperature sensor & gauge. 2003-2006 Evolution VIII & IX. STM-EVO-WN18NPT
	STM BOOST GAUGE INSTALL KIT This allows you to tap your mechanical gauge that uses the 1/8 tubing as a feed line. Universal Application. STM-BGIK
	PIGTAIL FUSES Trying to find a power source for your gauges? These nifty, little things will do the trick! Universal Application. STM-PIGF
	PROSPORT OIL FILTER ADAPTER PLATE (M20 x 1.5) This is a great product from Prosport to make installing your Oil Pressure and Oil Temperature senders easy. This plate screws on under your oil filter and it has 4 1/8"NPT fittings. M20 x 1.5 fits most Subaru, Non-metric Honda, Mitsubishi, Acura, Hyundai, Nissan Sentra 2.5L & Mazda RX-7, RX-8 & S2000. Universal Application. PSOPOT M20XP1.5
	PROSPORT WATER TEMP SENSOR ADAPTER This will place the temperature sensor directly in the stream of the water towards the radiator without absorbing transient heat from the engine block for accurate readings of the water temperature. Four sizes are available for the perfect fit for just about any engine application and stays water-tight to prevent leaks with the provided hose clamps. Each adapter features an 1/8 NPT fitting. Universal Application. PSWT3
	TUBING FOR MECHANICAL PSI GAUGES Auto Meter Nylon Tubing for Mechanical Pressure Gauges. Does not accommodate fuel pressure or models 5423 & 5426. Universal Application. 3223
	AUTOMETER ADAPTER (1/8" NPT-BSPT) Autometer Metric Gauge Adapter. 1/8" NPT Female to 1/8" BSPT Male Adapter. Universal Application. 2269
	-4AN MALE TO 1/8 NPT FEMALE ADAPTER FITTING -4AN Male to 1/8 NPT Female Adapter Fitting. Universal Application. TF-GA-04
	3M SUPER 33+ ELECTRICAL TAPE Scotch® Vinyl Electrical Tape 33 is a quality, general-purpose vinyl insulating tape. It has excellent resistance to: abrasion, moisture, alkalies, acid, copper corrosion and varying weather conditions. 3/4" x 52' Roll. 3MET33-10
	PROFITTER 500° LOW DENSITY PTFE PIPE TAPE 1/2" x 520" roll pipe sealing tape. 1/2" x 520" Roll. 63164
	VIBRANT POLYETHYLENE AIR LINE TUBING Flexible, lightweight and durable. Suitable for air lines and instrumentation and capable of Withstanding operating pressures up to 100 PSI and temperatures up to 140°F. Sold in a 10 foot roll and available in three diameters: 5/32", 3/8" and 1/4". Universal Application. 2650,2651,2652
	SILICONE VACUUM HOSE High quality, thick-walled, pure silicone hose in 3mm, 4mm and 6mm. Sold Per Foot. XXXXXX
	BLACK T-FITTINGS Black T Vacuum Fittings. 3, 4 and 6mm sizes. Universal Application. 10110,10109,12926,10108
EVOLUTION VIII-IX - OXYGEN SENSORS & PARTS      ///      BACK TO TOP
	OEM MITSUBISHI OXYGEN SENSORS Genuine OEM Mitsubishi Oxygen sensors. Front and rear O2 sensors available for all VIII-IX model years. 2003-2006 Evolution VIII-IX. MN153010,1588A064,MR578532,MN191125,1588A119
	AEM REPLACEMENT 4.9LSU BOSCH OXYGEN SENSOR AEM Replacement 4.9LSU Bosch Oxygen Sensor for new AEM Digital Wideband UEGO Air/Fuel Gauge 30-4110. Universal Application. 30-2004
	AEM REPLACEMENT 4.2LSU BOSCH OXYGEN SENSOR AEM Replacement 4.2LSU Bosch Oxygen Sensor for original AEM Wideband UEGO Air/Fuel Gauges. Universal Application. 30-2001
	AUTOMETER NARROW BAND O2 SENSOR KIT Auto Meter Narrow Band O2 Sensor Kit for use with narrow band air/fuel ratio gauges. Universal Application. 2244
	INNOVATE REPLACEMENT 02 SENSOR (LSU 4.2) Bosch LSU 4.2 5-Wire Wide-Band O2 Sensor. Compatible with Innovate Motorsports LM-1, LM-2, LC-1, and LC-1ST. Universal Application. 3737
	INNOVATE REPLACEMENT 02 SENSOR (LSU 4.9) Bosch LSU 4.9 5-Wire Wide-Band O2 Sensor. Compatible with Innovate Motorsports LM-2, LC-2, and MTX-L, SCG-1, DLG-1, PSB-1, and PSN-1. Universal Application. 17025,3888
	NGK NTK REPLACEMENT O2 SENSOR NGK / NTK replacement oxygen sensor sensor for the AFX wideband monitor. Universal Application. 24302
EVOLUTION VIII-IX - MAP & AIT SENSORS      ///      BACK TO TOP
	STM EVO 8/9 SPEED DENSITY SENSOR KIT If you're switching to Speed Density in your DSM, Evo 8 or 9, you'll need these sensors to get you on your way. The STM Speed Density Sensor Kit includes an AEM AIT sensor with aluminum weld bung and a 4 BAR Omni Power MAP Sensor. 2003-2006 Evolution VIII & IX. STM-EVO89/DSM-SDSK
	STM EVO 8/9 GM SPEED DENSITY SENSOR KIT The STM GM Speed Density Sensor Kit is a much more affordable alternative compared to AEM and includes the GM AIT sensor and matching harness, aluminum weld bung for your intercooler pipe and a 4 BAR Omni Power MAP Sensor. 2003-2006 Evolution VIII & IX. STM-KIT-EVO89/DSM-SDSK
	STM UNIVERSAL GM AIR INTAKE TEMPERATURE SENSOR KIT For a less expensive option to the AEM sensors, The STM GM Air Intake Temperature Sensor Kit includes an aluminum weld-on bung for your pipe, GM AIT sensor and matching pigtail harness. Universal Application. STM-GMAIT
	AEM AIR INLET TEMPERATURE SENSOR Air inlet temperature sensor kit. Includes aluminum weld-in bung, connector plug with flying lead & sensor. Universal Application. 30-2010
	DURALAST GM AIT SENSOR PIGTAIL HARNESS Duralast GM air intake temperature sensor female pigtail harness. Typically used with Mitsubishi DSM & Evolution speed density conversions. Universal Application. 235
	DURALAST GM AIT SENSOR Duralast GM 3/8" NPT air intake temperature sensor. Typically used with Mitsubishi DSM & Evolution speed density conversions Universal Application. SU-107
	OEM MITSUBISHI EVO 8/9 MAP SENSORS The Genuine OEM Mitsubishi MAP (Manifold Absolute Pressure) Sensors are different for the 043-04 and 05-06 Evo 8/9 models. 2003-2004 Evolution VIII. 2005-2006 Evolution VIII-IX. MN153281,MD305600
	OMNI POWER MITSUBISHI MAP SENSORS Omni Power USA 3 and 4 Bar MAP (Manifold Absolute Pressure) sensors use state of the art bipolar op amp circuitry with thin film resistor networks built into each micro chip. Pressure changes are calculated on a true linear 0-5 volt scale via a specially designed silicon pressure sensor that also compensates for temperature changes. 2003-2006 Evolution VIII & IX. MAP-MITS-3BR,MAP-MITS-4BR
	STM EVO 8/9 INTAKE MANIFOLD SENSOR ADAPTER The STM Intake Manifold Sensor Adapter gives you an 1/8" NPT thread allowing you to cleanly attach a map sensor, pressure sensor (or any sensor of your choice) directly on your Evo 8/9 or 95-99 DSM factory intake manifold. 2003-2006 Evolution VIII & IX. STM-EVO/DSM-MAP-F
	ENGLISH RACING EVO 8/9 AEM MAP SENSOR PLUG-N-PLAY HARNESS The English Racing AEM MAP Sensor Harness is a direct plug and play fit to easily connect the AEM MAP sensor to the stock Evo 8/9 harness. 2003-2006 Evolution VIII & IX. ER-MAP-PNP
	AEM REPLACEMENT MAP SENSOR KITS AEM Replacement MAP Sensor Kits include stainless steel sensor, connector, pins, 1/8" NPT to -4AN adapter & 1/8" NPT to 3/16" barb adapter. 1, 2, 3.5 and 5 BAR. Universal Application. 30-2130-15,30-2130-30,30-2130-50,30-2130-75
	AEM MAP SENSOR CONNECTOR AEM Map Sensor Connector. Universal Application. 35-2131
	AEM TRU-BOOST 5 BAR MAP SENSOR UPGRADE KIT AEM Tru-Boost 5 Bar MAP Sensor Upgrade Kit allows your Tru-Boost gauge the capability to read boost up to 50 psi. Universal Application. 30-4351
EVOLUTION VIII-IX - ENGINE, GAUGE & MISC SENSORS      ///      BACK TO TOP
	CRANK POSITION SENSOR OEM Mitsubishi Crank Position Sensor. 2003-2006 Evolution VIII & IX. MN158261
	CAMSHAFT POSITION SENSORS OEM Mitsubishi Camshaft Position Sensors for Evo VIII-IX. The exhaust cam sensor is the same for VIII & IX. The MIVEC IX uses the intake sensor also. 2003-2005 Evolution VIII CT9A 2006 Evolution IX MIVEC CT9A. MD327107,MR507814
	WATER TEMPERATURE SENSOR Genuine OEM Mitsubishi Water Temperature Sensor fits all 2003-2015 Evolution 8/9/X models as well as the 2G DSM (Eclipse GST/GSX & Talon TSi). 2003-2006 Evolution VIII & IX. 1308A012
	WATER TEMP GAUGE SENSOR Genuine OEM Mitsubishi Water Temperature Gauge Sensor. 2003-2006 Evolution VIII & IX. MD091056
	OIL PRESSURE SWITCH (2005) OEM Mitsubishi Oil Pressure Switches for Evolution VIII (August 2005 - November 2006 Build Date). Please confirm build date before purchase. Evolution VIII (August 2005 - November 2006 Build Dates). 1258A003
	OIL PRESSURE SWITCH (2006) OEM Mitsubishi Oil Pressure Switches for Evolution IX (December 2006+ Build Date). Please confirm build date before purchase. Evolution IX (December 2006+ Build Dates). MN163743
	IDLE AIR CONTROL MOTOR OEM Mitsubishi Idle Air Control Motor. 2003-2006 Evolution VIII & IX. 1450A069
	KNOCK SENSOR OEM Mitsubishi Knock Sensor. 2003-2006 Evolution VIII & IX. MR578117
	AEM REPLACEMENT PRESSURE SENSOR KITS AEM Replacement PSIg pressure sensors are available from 100-2000 psi for boost, EGT, nitrous, brake pressure, inlet air temperature, or UEGO replacement gauges. Universal Application. 30-2130-100,30-2130-150,30-2130-500,30-2130-1000,30-2130-2000
	AEM REPLACEMENT FLUID PRESSURE SENSORS AEM Replacement Fluid Pressure Sensors are available for 15, 35, 50, 100 and 150 PSI boost and fluid ranges. Compatible with AEM Analog and Digital Gauges. Universal Application. 30-2131-15G,30-2131-50,30-2131-75,30-2131-100,30-2131-150
	AEM REPLACEMENT FLUID TEMPERATURE SENSOR KIT AEM Replacement Oil/Trans/Water Temperature Sensor Kit includes the 1/8"NPT temperature sensor, plug, pins & pin lock. Compatible with digital and analog gauges. Universal Application. 30-2012
	AEM REPLACEMENT METHANOL INJECTION MONITOR SENSOR AEM Replacement Methanol Injection Monitor Sensor. Universal Application. 35-2128
	AEM REPLACEMENT ANALOG EGT K-TYPE SENSOR AEM Replacement EGT Sensor for Analog Gauges. K-Type Closed Tip Thermocouple Sensor. Universal Application. 30-2065
	AEM EXHAUST GAS TEMPERATURE SENSOR KIT The AEM 30-2050 EGT Sensor Kit is a RTD type EGT sensor with an inconel body, M14 x 6H. It includes an RTD temp sensor with male thread, a weld-on bung with female thread, connector and pins and offers a heat range of -40°F to 1832°F. Universal Application. 30-2050
	AEM UNIVERSAL 12 POSITION TRIM POT The AEM Universal 12 Position Trim Pot is for use on virtually any Engine Management System, such as the AEM EMS. Use the Trim Pot to adjust a number of trims, including ignition timing, fuel, boost, etc. Universal Application. 30-2056
EVOLUTION VIII-IX - CABLES, HARNESSES & WIRING      ///      BACK TO TOP
	STM EVO 8/9/X AEM UEGO SERIAL LOGGING CABLE The STM AEM UEGO EvoScan Serial Logging Cable allows you to directly log your AEM UEGO to your EvoScan. These offer professionally soldered contacts and 4 feet of blue, and 4 feet of black wire to remotely mount your cable almost anywhere under your dash for easy access while logging your AEM wideband! 2003-2006 Evolution VIII-IX. STM-EVOSCAN-LOG
	ENGLISH RACING EVO 8/9 AEM MAP SENSOR PLUG-N-PLAY HARNESS The English Racing AEM MAP Sensor Harness is a direct plug and play fit to easily connect the AEM MAP sensor to the stock Evo 8/9 harness. 2003-2006 Evolution VIII & IX. ER-MAP-PNP
	EVOSCAN OBD2 REFLASH CONNECTOR The EvoScan OBD2 Reflash Connector is an additional or replacement accessory for an OpenPort 2.0 cable for reflashing. EvoScan Openport 1.3R / 1.3U USB Cables do NOT need this adapter, this 12 pin connector is already permanently attached to those. 2003-2006 Evolution VIII-IX. MITSI_CONNECTOR
	SHERIDAN ENGINEERING ENGINE CONNECTOR KIT (EVO VIII) The Sheridan Engineering Engine Connector Kit for the 03-05 Evo 8 will allow vehicle owners to repair their harnesses, or build new ones. The kits include the connectors listed, wire terminals and seals. 2003-2005 Evolution VIII. KIT-03EVOBASE
	AEM INFINITY PLUG & PLAY HARNESS (EVO VIII) AEM Series 5 Infinity ECU plug & play harness with expansion port for the 2003-2005 Evolution VIII. 2003-2005 Evolution VIII. 30-3511
	AEM INFINITY PLUG & PLAY HARNESS (EVO IX) AEM Series 5 Infinity ECU plug & play harness with expansion port for the 2006 MIVEC Evolution IX. 2006 Evolution IX. 30-3512
	AEM INFINITY 02 SENSOR EXTENSION HARNESS The AEM Infinity 02 Sensor Extension Harness allows you to connect your AEM wideband O2 air/fuel ratio sensors to the Infinity's on-board wideband UEGO controllers. 72" length. Universal Application. 30-3600
	AEM INFINITY AUX HARNESS FOR AIT AND MAP SENSOR The AEM Infinity Aux Harness for AIT and MAP Sensor allows you to connect your AEM AIT and MAP sensors to the Infinity's Aux Deuatch Plug. 72" length. Universal Application. 30-3510-00
	AEM INFINITY IP67 COMMUNICATIONS CABLE Protect your AEM Infinity ECU by using IP67-rated communications cables. They are completely dustproof and are rated waterproof to 1 meter. Universal Application. 30-3601
	AEM INFINITY IP67 LOGGING CABLE Protect your AEM Infinity ECU by using IP67-rated communications cables. They are completely dustproof and are rated waterproof to 1 meter. Universal Application. 30-3602
	AEM PRESSURE SENSOR REPLACEMENT HARNESS FOR DIGITAL GAUGES The AEM Digital Boost/Pressure Gauge Replacement Cable replaces your old, damaged harness. This 8 foot cable fits AEM Digital Gauges (30-4401, 30-4406, 30-4407 & 30-4408). Universal Application. 35-3405
	AEM PRESSURE SENSOR REPLACEMENT HARNESS FOR ANALOG GAUGES AEM 96" Sensor Replacement Harness for Analog Boost/Fuel/Oil Pressure Gauges. Universal Application. 35-3412
	AEM REPLACEMENT TRU-BOOST 5 BAR MAP SENSOR HARNESS AEM 96" Replacement Harness for Tru-Boost 5 Bar MAP Sensor Upgrade Universal Application. 35-3410
	AEM TRU-BOOST GAUGE REPLACEMENT CABLE The AEM True-Boost Replacement Cable fits the AEM Digital Tru-Boost Gauge (30-4350) and is 8 feet long. Universal Application. 35-3409
	AEM REPLACEMENT UEGO POWER HARNESS The AEM Replacement UEGO Power Harness is compatible with both the Bosch 4.2 & 4.9 LSU sensors. 36" length. Universal Application. 35-3401
	AEM REPLACEMENT UEGO 4.2LSU OXYGEN SENSOR HARNESS AEM 96" Replacement UEGO 4.2LSU Oxygen Sensor Harness. Universal Application. 35-3400
	AEM REPLACEMENT UEGO 4.9LSU OXYGEN SENSOR HARNESS AEM 96" Replacement UEGO 4.9LSU Oxygen Sensor Harness. Universal Application. 35-3441
	AEM WIDEBAND FAILSAFE O2 SENSOR REPLACEMENT HARNESS AEM 96" 4.2LSU O2 Sensor Replacement Harness for Wideband Failsafe Gauge 30-4900. Universal Application. 35-3426
	AEM REPLACEMENT ANALOG TEMPERATURE SENSOR HARNESS AEM 96" Replacement Temperature Sensor Harness for the Oil/Transmission/Water Temp Analog Gauges. Universal Application. 35-3413
	AEM DIGITAL VOLT GAUGE POWER REPLACEMENT HARNESS AEM 36" Power Replacement Harness for Digital Volt Gauge 30-4400. Universal Application. 35-3403
	AEM DIGITAL TEMPERATURE GAUGE REPLACEMENT HARNESS AEM 96" Replacement Harness for the Digital Oil/Transmission/Water Temperature Gauge 30-4402. Universal Application. 35-3404
	AEM REPLACEMENT METH FLOW/FAILSAFE GAUGE USB CABLE AEM 96" Replacement USB Cable for AEM Meth Flow/Failsafe Gauges. Universal Product. 35-3415
	AEM REPLACEMENT ANALOG EGT SENSOR HARNESS AEM 96" Replacement EGT Sensor Harness for Analog Gauges. Universal Application. 35-3414
	AEM WIDEBAND FAILSAFE REPLACEMENT POWER HARNESS AEM 36" Replacement Power Harness for the Wideband Failsafe Gauge 30-4900. Universal Application. 35-3425
	AEM ANALOG GAUGE POWER HARNESS AEM 36" Power Replacement Cable for Analog Gauges. Universal Application. 35-3411
	AEM REPLACEMENT METH FAILSAFE OUTPUT HARNESS AEM 36" Replacement Output Harness for Water/Methanol Failsafe Gauges. Universal Product. 35-3418
EVOLUTION VIII-IX - SOLENOIDS      ///      BACK TO TOP
	GRIMMSPEED 3-PORT ELECTRONIC BOOST CONTROL SOLENOIDS Revolutionizing the boost solenoid market, GrimmSpeed has created model specific install brackets for a factory fit and finish. Features a plug & play fit to the OEM harness. GrimmSpeed worked with many of the top tuners in the country to ensure that this solenoid works safely with the factory ECU. 2003-2006 Evolution VIII-IX 057019
	AEM BOOST CONTROL SOLENOID AEM's Boost Control Solenoid is specifically manufactured for automotive applications. It is designed to resist corrosion and sticking from exposure to rich fuel mixtures. AEM's Boost Control Solenoid is pressure tested to 100 PSI and includes 1/8" NPT to 3/8" barb fittings to reduce any chance of leaks. Universal Application. 30-2400
	PERRIN 3-PORT ELECTRONIC BOOST CONTROL SOLENOID The EBCS PRO operates almost 2 times faster than other designs, allowing almost 50% more airflow, and works with OEM ECUs without causing check engine lights. To fully utilize the EBCS Pro, an ECU recalibration is NEEDED to ensure no overboosting occurs. The OEM male connector is specific to all Subaru and Mitsubishi applications. Includes additional brackets to allow universal applications. Universal Application. ASM-TAC-726
	OEM MITSUBISHI BOOST CONTROL SOLENOID Genuine OEM Mitsubishi Boost Control Solenoid. 2003-2006 Evolution VIII & IX. MN143554

CSS