|
EVOLUTION X - GAUGE INSTALLATION
///
BACK TO TOP |
|
|
STM EVO X REMOTE OIL PRESSURE LINE KIT (BACK OF BLOCK)
The STM Remote Oil Pressure Line Kit works with 1/8" NPT gauges and installs in place of your factory oil pressure switch in the back of your engine block allowing you to relocate your new oil pressure sending unit away from the harsh vibrations of the engine, keeping your sending unit safe and prolonging life. Works with both 4G63 and 4B11 Evolution 8/9/X.
2008-2015 Evolution X.
STM-EVO-89-REMOTE-OP |
|
STM BOOST GAUGE INSTALL KIT
This allows you to tap your mechanical gauge that uses the 1/8 tubing as a feed line.
Universal Application.
STM-BGIK |
|
PIGTAIL FUSES
Trying to find a power source for your gauges? These nifty, little things will do the trick!
Universal Application.
STM-PIGF |
|
PROSPORT OIL FILTER ADAPTER PLATE (M20 x 1.5)
This is a great product from Prosport to make installing your Oil Pressure and Oil Temperature senders easy. This plate screws on under your oil filter and it has 4 1/8"NPT fittings. M20 x 1.5 fits most Subaru, Non-metric Honda, Mitsubishi, Acura, Hyundai, Nissan Sentra 2.5L & Mazda RX-7, RX-8 & S2000.
Universal Application.
PSOPOT M20XP1.5 |
|
PROSPORT WATER TEMP SENSOR ADAPTER
This will place the temperature sensor directly in the stream of the water towards the radiator without absorbing transient heat from the engine block for accurate readings of the water temperature. Four sizes are available for the perfect fit for just about any engine application and stays water-tight to prevent leaks with the provided hose clamps. Each adapter features an 1/8 NPT fitting.
Universal Application.
PSWT3 |
|
TUBING FOR MECHANICAL PSI GAUGES
Auto Meter Nylon Tubing for Mechanical Pressure Gauges. Does not accommodate fuel pressure or models 5423 & 5426.
Universal Application.
3223 |
|
AUTOMETER ADAPTER (1/8" NPT-BSPT)
Autometer Metric Gauge Adapter. 1/8" NPT Female to 1/8" BSPT Male Adapter.
Universal Application.
2269 |
|
-4AN MALE TO 1/8 NPT FEMALE ADAPTER FITTING
-4AN Male to 1/8 NPT Female Adapter Fitting.
Universal Application.
TF-GA-04 |
|
3M SUPER 33+ ELECTRICAL TAPE
Scotch® Vinyl Electrical Tape 33 is a quality, general-purpose vinyl insulating tape. It has excellent resistance to: abrasion, moisture, alkalies, acid, copper corrosion and varying weather conditions.
3/4" x 52' Roll.
3MET33-10 |
|
PROFITTER 500° LOW DENSITY PTFE PIPE TAPE
1/2" x 520" roll pipe sealing tape.
1/2" x 520" Roll.
63164 |
|
VIBRANT POLYETHYLENE AIR LINE TUBING
Flexible, lightweight and durable. Suitable for air lines and instrumentation and capable of Withstanding operating pressures up to 100 PSI and temperatures up to 140°F. Sold in a 10 foot roll and available in three diameters: 5/32", 3/8" and 1/4".
Universal Application.
2650,2651,2652 |
|
SILICONE VACUUM HOSE
High quality, thick-walled, pure silicone hose in 3mm, 4mm and 6mm.
Sold Per Foot.
XXXXXX |
|
BLACK T-FITTINGS
Black T Vacuum Fittings. 3, 4 and 6mm sizes.
Universal Application.
10110,10109,12926,10108 |
|
|
EVOLUTION X - OXYGEN SENSORS & PARTS
///
BACK TO TOP |
|
|
OEM MITSUBISHI OXYGEN SENSORS
Genuine OEM Mitsubishi Oxygen sensors. Front and rear O2 sensors available.
2008-2015 Evolution X.
1588A141,1588A144 |
|
AEM REPLACEMENT 4.9LSU BOSCH OXYGEN SENSOR
AEM Replacement 4.9LSU Bosch Oxygen Sensor for new AEM Digital Wideband UEGO Air/Fuel Gauge 30-4110.
Universal Application.
30-2004 |
|
AEM REPLACEMENT 4.2LSU BOSCH OXYGEN SENSOR
AEM Replacement 4.2LSU Bosch Oxygen Sensor for original AEM Wideband UEGO Air/Fuel Gauges.
Universal Application.
30-2001 |
|
AUTOMETER NARROW BAND O2 SENSOR KIT
Auto Meter Narrow Band O2 Sensor Kit for use with narrow band air/fuel ratio gauges.
Universal Application.
2244 |
|
INNOVATE REPLACEMENT 02 SENSOR (LSU 4.2)
Bosch LSU 4.2 5-Wire Wide-Band O2 Sensor. Compatible with Innovate Motorsports LM-1, LM-2, LC-1, and LC-1ST.
Universal Application.
3737 |
|
INNOVATE REPLACEMENT 02 SENSOR (LSU 4.9)
Bosch LSU 4.9 5-Wire Wide-Band O2 Sensor. Compatible with Innovate Motorsports LM-2, LC-2, and MTX-L, SCG-1, DLG-1, PSB-1, and PSN-1.
Universal Application.
17025,3888 |
|
NGK NTK REPLACEMENT O2 SENSOR
NGK / NTK replacement oxygen sensor sensor for the AFX wideband monitor.
Universal Application.
24302 |
|
|
EVOLUTION X - MAF, MAS, MAP & AIT
///
BACK TO TOP |
|
|
3 BAR MAP SENSOR
Genuine OEM Mitsubishi 3 Bar Map Sensor.
2008-2015 Evolution X.
1865A052 |
|
OMNI POWER MITSUBISHI MAP SENSORS
Omni Power USA 3 and 4 Bar MAP (Manifold Absolute Pressure) sensors use state of the art bipolar op amp circuitry with thin film resistor networks built into each micro chip. Pressure changes are calculated on a true linear 0-5 volt scale via a specially designed silicon pressure sensor that also compensates for temperature changes.
2008-2015 Evolution X.
MAP-MITS-3BR,MAP-MITS-4BR |
|
AEM MAP SENSOR KITS
3.5 bar map or 5 bar map sensor kit. Includes: Stainless Steel Sensor, Connector, Pins, 1/8" NPT to -4 Adapter & 1/8" NPT to 3/16" Barb Adapter.
Universal Application.
30-2130-50,30-2130-75 |
|
AEM MAP SENSOR CONNECTOR
AEM Map Sensor Connector.
Universal Application.
35-2131 |
|
GENUINE OEM MITSUBISHI EVO X MASS AIR FLOW SENSOR
Genuine OEM Mitsubishi Mass Air Flow Sensor fits all 2008-2015 Mitsubishi Lancer Evolution X models.
2008-2015 Evolution X.
MR985187 |
|
WATER TEMPERATURE SENSOR
Genuine OEM Mitsubishi Water Temperature Sensor fits all 2003-2015 Evolution 8/9/X models as well as the 2G DSM (Eclipse GST/GSX & Talon TSi).
2008-2015 Evolution X.
1308A012 |
|
|
AEM REPLACEMENT MAP SENSOR KITS
AEM Replacement MAP Sensor Kits include stainless steel sensor, connector, pins, 1/8" NPT to -4AN adapter & 1/8" NPT to 3/16" barb adapter. 1, 2, 3.5 and 5 BAR.
Universal Application.
30-2130-15,30-2130-30,30-2130-50,30-2130-75 |
|
|
AEM MAP SENSOR CONNECTOR
AEM Map Sensor Connector.
Universal Application.
35-2131 |
|
AEM TRU-BOOST 5 BAR MAP SENSOR UPGRADE KIT
AEM Tru-Boost 5 Bar MAP Sensor Upgrade Kit allows your Tru-Boost gauge the capability to read boost up to 50 psi.
Universal Application.
30-4351 |
|
AEM AIR INLET TEMPERATURE SENSOR
Air inlet temperature sensor kit. Includes aluminum weld-in bung, connector plug with flying lead & sensor.
Universal Application.
30-2010 |
|
STM UNIVERSAL GM AIR INTAKE TEMPERATURE SENSOR KIT
For a less expensive option to the AEM sensors, The STM GM Air Intake Temperature Sensor Kit includes an aluminum weld-on bung for your pipe, GM AIT sensor and matching pigtail harness.
Universal Application.
STM-GMAIT |
|
DURALAST GM AIT SENSOR PIGTAIL HARNESS
Duralast GM air intake temperature sensor female pigtail harness. Typically used with Mitsubishi DSM & Evolution speed density conversions.
Universal Application.
235 |
|
DURALAST GM AIT SENSOR
Duralast GM 3/8" NPT air intake temperature sensor. Typically used with Mitsubishi DSM & Evolution speed density conversions
Universal Application.
SU-107 |
|
|
EVOLUTION X - ENGINE, GAUGE & MISC SENSORS & RELAYS
///
BACK TO TOP |
|
|
OEM MITSUBISHI OIL PRESSURE SWITCH
Genuine OEM Mitsubishi Oil Pressure Switch.
2008-2015 Evolution X.
MN163743 |
|
MITSUBISHI EVO X COLD START RELAY REPLACEMENT KIT
The Mitsubishi Service Bulletin TSB-10-13-002 for Evolution X models built prior to November 16, 2009 address a cold-start issue with the relays in the fuse box.
2008-2015 Evolution X.
8627A049,MR400709 |
|
OEM EVO X UPGRADED FUEL PUMP RELAY
If you haven't upgraded to this new, green relay, you need to! The old relay has been known to fail and cause serious engine problems. Swap it out as soon as possible.
2008-2015 Evolution X.
8627A011 |
|
AEM REPLACEMENT PRESSURE SENSOR KITS
AEM Replacement PSIg pressure sensors are available from 100-2000 psi for boost, EGT, nitrous, brake pressure, inlet air temperature, or UEGO replacement gauges.
Universal Application.
30-2130-100,30-2130-150,30-2130-500,30-2130-1000,30-2130-2000 |
|
AEM REPLACEMENT FLUID PRESSURE SENSORS
AEM Replacement Fluid Pressure Sensors are available for 15, 35, 50, 100 and 150 PSI boost and fluid ranges. Compatible with AEM Analog and Digital Gauges.
Universal Application.
30-2131-15G,30-2131-50,30-2131-75,30-2131-100,30-2131-150 |
|
AEM REPLACEMENT FLUID TEMPERATURE SENSOR KIT
AEM Replacement Oil/Trans/Water Temperature Sensor Kit includes the 1/8"NPT temperature sensor, plug, pins & pin lock. Compatible with digital and analog gauges.
Universal Application.
30-2012 |
|
AEM REPLACEMENT METHANOL INJECTION MONITOR SENSOR
AEM Replacement Methanol Injection Monitor Sensor.
Universal Application.
35-2128 |
|
AEM REPLACEMENT ANALOG EGT K-TYPE SENSOR
AEM Replacement EGT Sensor for Analog Gauges. K-Type Closed Tip Thermocouple Sensor.
Universal Application.
30-2065 |
|
AEM EXHAUST GAS TEMPERATURE SENSOR KIT
The AEM 30-2050 EGT Sensor Kit is a RTD type EGT sensor with an inconel body, M14 x 6H. It includes an RTD temp sensor with male thread, a weld-on bung with female thread, connector and pins and offers a heat range of -40°F to 1832°F.
Universal Application.
30-2050 |
|
AEM UNIVERSAL 12 POSITION TRIM POT
The AEM Universal 12 Position Trim Pot is for use on virtually any Engine Management System, such as the AEM EMS. Use the Trim Pot to adjust a number of trims, including ignition timing, fuel, boost, etc.
Universal Application.
30-2056 |
|
|
EVOLUTION X - CABLES & HARNESSES
///
BACK TO TOP |
|
|
STM EVO 8/9/X AEM UEGO SERIAL LOGGING CABLE
The STM AEM UEGO EvoScan Serial Logging Cable allows you to directly log your AEM UEGO to your EvoScan. These offer professionally soldered contacts and 4 feet of blue, and 4 feet of black wire to remotely mount your cable almost anywhere under your dash for easy access while logging your AEM wideband!
2008-2015 Evolution X.
STM-EVOSCAN-LOG |
|
COBB AP3 OBDII UNIVERSAL ACCESSPORT CABLE
Tired of your Accessport OBDII cable getting in the way? The new COBB OBDII Universal Cable features a much lower profile OBD connector design. The 6ft cable allows for a cleaner installation when choosing to route behind the dash.
Universal Application.
AP3-OBDII-CABLE-UNIVERSAL |
|
AEM INFINITY SERIES 7 UNIVERSAL PLUG & PIN KIT
The AEM Infinity Series 7 Universal Plug & Pin Kit includes (1) 73-pin connector with cover, (1) 56-pin connector with cover, 130 small pins, 1 large pin with weather seal, 1 micro relay with pins, and 30 sealing plugs. AEM offers several different wiring harness types and configurations to simplify the process of wiring the Infinity ECU to your vehicle.
Universal Application.
30-3701 |
|
AEM INFINITY SERIES 7 UNIVERSAL WIRING HARNESS
The AEM Infinity Series 7 Universal Wiring Harness includes pre-wired power and grounds, power relay, fuse box, dual wideband connectors, AEMnet connector (CAN), 100 X 96" terminated wires for population and 12 small pins. AEM offers several different wiring harness types and configurations to simplify the process of wiring the Infinity ECU to your vehicle.
Universal Application.
30-3702 |
|
AEM INFINITY SERIES 7 MINI UNIVERSAL WIRING HARNESS
The AEM Infinity Series 7 Mini Universal Harness includes pre-wired power and grounds, power relay, fuse box, dual wideband connectors, AEMnet connector (CAN), 100 small pins with 30 sealing plugs. AEM offers several different wiring harness types and configurations to simplify the process of wiring the Infinity ECU to your vehicle.
Universal Application.
30-3703 |
|
AEM INFINITY SERIES 5 PLUG & PIN KIT
The AEM Infinity Series 5 Plug & Pin Kit includes 80 pin connector with cover, 80 small pins, 1 micro relay with pins and 30 sealing plugs. AEM offers several different wiring harness types and configurations to simplify the process of wiring the Infinity ECU to your vehicle.
Universal Application.
30-3704 |
|
AEM INFINITY SERIES 5 MINI UNIVERSAL WIRING HARNESS
The AEM Infinity Series 5 Mini Universal Harness includes pre-wired power, grounds, power relay, fuse box, single wideband & AEMnet, 80 small pins and 30 sealing plugs. AEM offers several different wiring harness types and configurations to simplify the process of wiring the Infinity ECU to your vehicle.
Universal Application.
30-3705 |
|
AEM INFINITY SERIES 5 UNIVERSAL MINI FLYING LEAD HARNESS
The AEM Infinity Series 5 Universal Mini Flying Lead Harness includes pre-wired power, grounds, power relay, single wideband, 8 x coils & 8 x injectors. I/O wiring includes TPS, MAP, CLT, AIT, +5V, Sensor Ground, Fan, Tach & 2 Step. 10 x 96" 22ga Terminated wire and 2 x 96" Terminated 2-Pair Twisted/Shielded Wire. AEM offers several different wiring harness types and configurations to simplify the process of wiring the Infinity ECU to your vehicle.
Universal Application.
30-3706 |
|
AEM INFINITY 02 SENSOR EXTENSION HARNESS
The AEM Infinity 02 Sensor Extension Harness allows you to connect your AEM wideband O2 air/fuel ratio sensors to the Infinity's on-board wideband UEGO controllers. 72" length.
Universal Application.
30-3600 |
|
AEM INFINITY AUX HARNESS FOR AIT AND MAP SENSOR
The AEM Infinity Aux Harness for AIT and MAP Sensor allows you to connect your AEM AIT and MAP sensors to the Infinity's Aux Deuatch Plug. 72" length.
Universal Application.
30-3510-00 |
|
AEM INFINITY IP67 COMMUNICATIONS CABLE
Protect your AEM Infinity ECU by using IP67-rated communications cables. They are completely dustproof and are rated waterproof to 1 meter.
Universal Application.
30-3601 |
|
AEM INFINITY IP67 LOGGING CABLE
Protect your AEM Infinity ECU by using IP67-rated communications cables. They are completely dustproof and are rated waterproof to 1 meter.
Universal Application.
30-3602 |
|
AEM PRESSURE SENSOR REPLACEMENT HARNESS FOR DIGITAL GAUGES
The AEM Digital Boost/Pressure Gauge Replacement Cable replaces your old, damaged harness. This 8 foot cable fits AEM Digital Gauges (30-4401, 30-4406, 30-4407 & 30-4408).
Universal Application.
35-3405 |
|
AEM PRESSURE SENSOR REPLACEMENT HARNESS FOR ANALOG GAUGES
AEM 96" Sensor Replacement Harness for Analog Boost/Fuel/Oil Pressure Gauges.
Universal Application.
35-3412 |
|
AEM REPLACEMENT TRU-BOOST 5 BAR MAP SENSOR HARNESS
AEM 96" Replacement Harness for Tru-Boost 5 Bar MAP Sensor Upgrade
Universal Application.
35-3410 |
|
AEM TRU-BOOST GAUGE REPLACEMENT CABLE
The AEM True-Boost Replacement Cable fits the AEM Digital Tru-Boost Gauge (30-4350) and is 8 feet long.
Universal Application.
35-3409 |
|
AEM REPLACEMENT UEGO POWER HARNESS
The AEM Replacement UEGO Power Harness is compatible with both the Bosch 4.2 & 4.9 LSU sensors. 36" length.
Universal Application.
35-3401 |
|
AEM REPLACEMENT UEGO 4.2LSU OXYGEN SENSOR HARNESS
AEM 96" Replacement UEGO 4.2LSU Oxygen Sensor Harness.
Universal Application.
35-3400 |
|
AEM REPLACEMENT UEGO 4.9LSU OXYGEN SENSOR HARNESS
AEM 96" Replacement UEGO 4.9LSU Oxygen Sensor Harness.
Universal Application.
35-3441 |
|
AEM WIDEBAND FAILSAFE O2 SENSOR REPLACEMENT HARNESS
AEM 96" 4.2LSU O2 Sensor Replacement Harness for Wideband Failsafe Gauge 30-4900.
Universal Application.
35-3426 |
|
AEM REPLACEMENT ANALOG TEMPERATURE SENSOR HARNESS
AEM 96" Replacement Temperature Sensor Harness for the Oil/Transmission/Water Temp Analog Gauges.
Universal Application.
35-3413 |
|
AEM DIGITAL VOLT GAUGE POWER REPLACEMENT HARNESS
AEM 36" Power Replacement Harness for Digital Volt Gauge 30-4400.
Universal Application.
35-3403 |
|
AEM DIGITAL TEMPERATURE GAUGE REPLACEMENT HARNESS
AEM 96" Replacement Harness for the Digital Oil/Transmission/Water Temperature Gauge 30-4402.
Universal Application.
35-3404 |
|
AEM REPLACEMENT METH FLOW/FAILSAFE GAUGE USB CABLE
AEM 96" Replacement USB Cable for AEM Meth Flow/Failsafe Gauges.
Universal Product.
35-3415 |
|
AEM REPLACEMENT ANALOG EGT SENSOR HARNESS
AEM 96" Replacement EGT Sensor Harness for Analog Gauges.
Universal Application.
35-3414 |
|
AEM WIDEBAND FAILSAFE REPLACEMENT POWER HARNESS
AEM 36" Replacement Power Harness for the Wideband Failsafe Gauge 30-4900.
Universal Application.
35-3425 |
|
AEM ANALOG GAUGE POWER HARNESS
AEM 36" Power Replacement Cable for Analog Gauges.
Universal Application.
35-3411 |
|
AEM REPLACEMENT METH FAILSAFE OUTPUT HARNESS
AEM 36" Replacement Output Harness for Water/Methanol Failsafe Gauges.
Universal Product.
35-3418 |
|
|
EVOLUTION X - SOLENOIDS
///
BACK TO TOP |
|
|
GRIMMSPEED 3-PORT ELECTRONIC BOOST CONTROL SOLENOIDS
Revolutionizing the boost solenoid market, GrimmSpeed has created model specific install brackets for a factory fit and finish. Features a plug & play fit to the OEM harness. GrimmSpeed worked with many of the top tuners in the country to ensure that this solenoid works safely with the factory ECU.
2008-2015 Evolution X
057033 |
|
AEM BOOST CONTROL SOLENOID
AEM's Boost Control Solenoid is specifically manufactured for automotive applications. It is designed to resist corrosion and sticking from exposure to rich fuel mixtures. AEM's Boost Control Solenoid is pressure tested to 100 PSI and includes 1/8" NPT to 3/8" barb fittings to reduce any chance of leaks.
Universal Application.
30-2400 |
|
PERRIN 3-PORT ELECTRONIC BOOST CONTROL SOLENOID
The EBCS PRO operates almost 2 times faster than other designs, allowing almost 50% more airflow, and works with OEM ECUs without causing check engine lights. To fully utilize the EBCS Pro, an ECU recalibration is NEEDED to ensure no overboosting occurs. The OEM male connector is specific to all Subaru and Mitsubishi applications. Includes additional brackets to allow universal applications.
Universal Application.
ASM-TAC-726 |
|
